Battery Test Chamber Manufacturer

Battery Test Chamber

BATTERY TEST CHAMBER CONSTRUCTION

Construction is a general term meaning the art and science to form objects and system.

INNER CHAMBER

Inner chamber is made of Stainless steel 304 grade steel.

OUTER CHAMBER

Outer chamber is made of galvanized steel sheet duly powder coated.

DOOR

Door is made of steel sheet duly powder coated.

Automatically Cut-Off The Measurements and an alarm ring whenever the door is opened/not air tight.

TRAY

Battery Test Chamber platform trays have a provision to slide inside out for the placement of the detector.

The inner chamber space provided with provision for placing 04 wire mesh trays.

Battery   Test    Chamber Dimensions of the inner chamber and the sliding tray are provided as per design.

Alter These dimensions as per their tolerance making sure that the sliding tray is able to accommodate samples.

Battery Test Chamber Adjustable 4 platform trays with adjustable height arrangement in the inner chamber.

AIR-CONDITIONING CHANNEL

Evaporators, drainage, and the dry to prevent.

ADJUST FEET AND WHEEL

Adjust feet: 4 castors , Mobile support chamber

CONTROL PANEL

Battery Test Chamber Temperature (humidity) control display, over-temperature protection Setting device, emergency stop switch, fault indicator light, and buzzer.

BATTERY TEST CHAMBER MECHANICAL ROOM:

Battery Test Chamber Included in the mechanical room Refrigeration units, power Distribution control cabinet.

BATTERY TEST CHAMBER DISTRIBUTION CONTROL CABINET
  • Distribution board.
  • Sample test terminal.
  • Total power leakage circuit breakers.
  • Connectors able to withstand 800V and handle low leakage

Battery Test Chamber

Roch Mechatronics Inc is a reputed manufacture & supplier of Battery Test Chamber have been the choice for portable electronic devices. As they now become important for electric vehicles, reliability and safety become paramount. The batteries must perform well in hot and cold conditions, while not posing a hazard due to leaking or exploding.

Through temperature testing with ESPEC chambers, the batteries’ ability to withstand environmental extremes and stress can be identified safely.

  • Temperature range: -40 °C to +110 °C
  • Class 2 independent temperature safety device when the temperature is set to 120 °C
  • A reversible stainless steel pressure relief flap is installed in the middle on top of the unit
  • Enhanced door-locking mechanism with reinforced brackets
  • Monitoring of CO, H₂, O₂, and temperature in the testing area atmosphere
  • Inertization equipment
  • CO₂ fire suppression equipment
  • Voltage precision with <100ppm and current range with 1Ma to 10 A in 4 ranges.
  • Current accuracy: 02% of FSR or lower
  • Measurement resolution: 24 bit or better as per requirement
  • Rise trime:0.1mS or better as per their requirement
  • Strong electromagnetic emission source testing or storage of the
  • Circuit type: true bipolar linear, allows cross zero linearity
  • 4 probe type cell
  • All the channel which is independent and capable of charge- disharge cycling of
  • the channel which is galvanostate/ potentiostate
  • Channel parelling option which is available for all 8 channels to apply and measure higher current; +-80 A of max current when channels are
MAKERoch Mechatronics Inc.
MODEL NOB-TC-234
Temperature range-40 °C to +110 °C
Temperature Stability<+ 1.0°C
Temperature Uniformity< + 2°C
Relative Humidity Range(Optional)30 % to 98%RH ±3% RH
Humidity Accuracies (Optional)Set Point Fluctuation: ±3% RH
Outer box (chamber) (Material)galvanized steel
DoorInsulated door with viewing window of size 700 x 700 mm with condensation free heaters. Sensors for detection of open door and safety shut-down of
chamber operation and alert message on the screen.
Door SealingSilicon Door Gasket
Inner Box holding sliding platform TraysSS-304
Material
Inner Dimensions(W X D X H)(750 x 900 x1200 mm) 2.5ft x 3ft x 4ft
Weight of sample7kg to 100 kg
Doorgalvanized sheet Powder coating .
Power supply415 ± 10 %V ,3 Phase+ N 50 HZ AC

HEATER:

  • Nickel-chromium alloy heating wire
  • Battery Test Chamber Heater control mode: no contact cycle pulse width modulation, SSR (solid state relay).
  • Battery Test Chamber power cord hole and drainage systems: On the back of the test

REFRIGERATION  COMPRESSORS:

Hermetically sealed compressors.

EVAPORATOR

Battery Test Chamber Finned-tube heat exchanger.

CONDENSER

Battery Test Chamber

Finned-tube heat exchanger.

THROTTLING DEVICE

Battery Test Chamber Thermostatic expansion valve, capillary.

REFRIGERATOR CONTROL

Battery Test Chamber Under the test conditions, the PLC (Programmable Logic Controller) control systems automatically adjust the operating conditions of the refrigerator, the compressor back to the gas cooling circuit, energy regulation loop.

CONTROL SYSTEM DISPLAY

Color  LCD display

OPERATION WAY

Battery Test Chamber

Program control.

SETTING WAY

Battery Test Chamber

English menu, input. PROGRAM CAPACITY (OPTIONAL)

Battery Test Chamber 10 programs. Each program step 3; each program can be set to 999 cycles

Input: Thermocouple REFRIGERATION:

The system is based on either a single stage or a cascade refrigeration system.

Safety features – ensure your technicians are never in harm’s way. These features reduce the chance of an explosion and minimize the damaging effects of a spark-induced explosion. Here are some additional options available on your battery test chambers:

  • Automatic Door Locks
  • Blow Off Top
  • Chain Lock Door
  • Explosion Proof Interior Light
  • Exterior Light
  • Gas Detector/Monitor
  • Fire Suppression System
  • Hand Wheel Door Latch
  • Handle/Latch
  • Intrinsic Safety Isolation Barrier
  • Nitrogen Purge
  • Non-Sparking Fan Blade
  • Reinforced Floor
MAKERoch Mechatronics Inc.
MODEL NOB-TC-234
Temperature range-40 °C to +110 °C
Temperature Stability<+ 1.0°C
Temperature Uniformity< + 2°C
Relative Humidity Range(Optional)30 % to 98%RH ±3% RH
Humidity Accuracies (Optional)Set Point Fluctuation: ±3% RH
Outer box (chamber) (Material)galvanized steel
DoorInsulated door with viewing window of size 700 x 700 mm with condensation free heaters. Sensors for detection of open door and safety shut-down of
chamber operation and alert message on the screen.
Door SealingSilicon Door Gasket
Inner Box holding sliding platform TraysSS-304
Material
Inner Dimensions(W X D X H)(750 x 900 x1200 mm) 2.5ft x 3ft x 4ft
Weight of sample7kg to 100 kg
Doorgalvanized sheet Powder coating .
Power supply415 ± 10 %V ,3 Phase+ N 50 HZ AC